![]() ![]() Put some POR-15 Epoxy Putty In your toolbox today. Apply a coat of the primer over the finished surface. So, this moldable epoxy putty can be used to fix leaking basement walls, swimming pools, plumbing fixtures, and so much more.Allow to dry and apply another coat if needed.Allow to dry for 4 -6 hours and sand using water emery grit 180.Apply a thin coat of KPF using a putty knife.Primers soluble in mineral turpentine oil are compatible with KPF. Recoating Time - 4 - 6 hours after application.Drying time - Surface dry time 30 minutes max.Hard dry - Upon air-drying, it dries hard. Download this stock image: Putty knife with tub of paste for wood and metal - 2D8PDW0 from Alamys library of millions of high resolution stock photos.Can be thinned - Can be thinned to desired consistency by using mineral turpentine oil.Easy to apply - Easily applied by putty knife.Ready to use - Comes in ready to use consistency.This product can be used in combination with any solvent based wood or metal primer. It is grey in colour and is supplied in a paste consistency. You will need a PDF reader to view these links, you can download Acrobat Reader for free from Adobe’s website.Asian Paints Knifing Paste Filler is a ready to use solvent-based filler that can be used to fill and level dents on wood and metal surfaces. For additional information refer to the Sculpwood Epoxy Paste Safety Data Sheet. Check the shipping options page for details on shipping hazardous items. Sculpwood Epoxy Paste is a hazardous product. IMPROPER MIXING IS THE GREATEST CAUSE OF EPOXY SYSTEMS FAILURE. Tan (Part A) White (Part B) / Beige (Mixed)Ĥ Hours (By hand or block) / 7 Hours (Machine sand) Technical Data / Properties Viscosity 77☏ (25☌) cps If you wish to mix by weight the ratio is one part A to one part B. If the Sculpwood Putty is going to be color-toned with our Epoxy Coloring Agent, the toning colorant can be added in small amounts after the Sculpwood Putty is mixed. There is a ☑0% mix-error margin so volume amounts can usually be judged by eye. Equal amounts by volume are put on the board surface, and then folded and kneaded until a consistent color is obtained. SculpWood Putty is most easily mixed by hand, using disposable gloves. NOTES: For best results, apply at 50☏ (5☌) or above. Measure and mix only enough SculpWood that can be applied in the indicated working time. Let the S-1 Sealer cure before applying the SculpWood Putty. In most cases, applying S-1 Epoxy Sealer as a primer is recommended. If necessary, sand surface with 80–120 grit paper. APPLICATION:Įnsure surfaces to be repaired are clean, free, of dust, grease, or dirt. Separation does not harm the quality of the product. If separation occurs, simply remix ingredients, and use as normal. C.), or for longer periods, please check for separation of the resin from the additives. Storage of this product in higher temperatures, or for longer than 3 years, can lead to ingredient separation. SculpWood Moldable Epoxy Putty is available in 8 oz, 2 Pint, 2 Quart and 2 Gallon units. ![]() ![]() Resin and hardener are easily mixed by hand.Features a convenient 1:1 mixing ratio.Will not shrink or become brittle after curing.Use to replace rotted or chipped away wood cracks and other defects in window and door sills, frames, railings, furniture, etc. It is easily sanded and will accept paint, screws and nails. It has excellent adhesion to wood, stone, metal, and most plastics with the exception of plastics in the polyethylene family. It is moldable, carvable, lightweight, strong, and exhibits excellent adhesion to a variety of substrates. Allow to dry for 4 -6 hours and sand using water emery grit 180. SculpWood Putty is a two-component, solvent-free, kneadable epoxy. Apply a thin coat of KPF using a putty knife. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |